Device Core Articles

Introduction to Blue Pill Device Cores

AJA FrameSync Video Channels

When controlling individual video channels of an AJA FS series frame sync, it is important to add...

Arri Camera settings

The SKAARHOJ Arri device core can control Arri Cameras over CAP and older cameras over SSCP.Pleas...

Biamp Tesira

The Biamp Tesira core has two different models, the Manual model and the Auto model. Manual Mode...

BirdDog Cameras

All Blue Pill integrations for the BirdDog cameras have been made using their NDI 5 firmwares. S...

Blackmagic Camera Control via Atem

It is possible to control your Blackmagic cameras through an Atem switcher using your Skaarhoj Bl...

Blackmagic Camera Control via Rest API

Firstly you need to download and install Blackmagic Camera Setup program from here https://www.bl...

Canon EOS C500 and EOS C300 (Canon-XC)

The currently recomended Core version for EOS C500 and EOS C300 is depended on the firmware versi...

Clear-Com Station-IC

To connect the device core to Clear-Com, you need a Clear-Com Station IC client installed on your...

Dante

The Dante API Device Core lets a SKAARHOJ controller drive audio and video routing on a Dante n...

DataVideo PTR-10 and PTC-150

Some DataVideo devices only support their proprietary DVIP protocol over the network. For connect...

Densitron UReady 1U and UReady 2U Displays with Raw Panel 🔑

The SKAARHOJ xpanel-touch package allows users to create browser-accessible software UIs, appeari...

Device Core Link (DCLink) 🔑

The Blue Pill app called dclink-tcp is designed to provide a simple, unified TCP based ASCII inte...

DreamChip Camera Setup and Test

This guide outlines cabling workflows to connect DreamChip cameras to SKAARHOJ-recommended third-...

Ember+ DeviceCore

The Ember+ DeviceCore allows bluepills to control Ember+ Systems as Consumers. Using the built in...

Eth-B4 Link Lens Control

Skaarhoj Eth-B4 Link offer a way to control iris on B4 lens separate from the camera they are con...

HID devices on Raw Panel 🔑

With SKAARHOJs HID application (xpanel-hids package) you can connect one or more particular USB d...

HTTP Device Core

The HTTP Device Core for Blue Pill, core-protocol-http, allows users to send and to some extend r...

Kessler Crane

Adding and connecting to a Kessler Crane device from the Blue Pill platform The Blue pill can co...

MRMC Flair 7 Control with SKAARHOJ

Flair is an industry-leading software solution from Mark Roberts Motion Control used to control c...

NETIO PDU settings

NETIO PDU's (Power Distribution Units) are network-based power sockets. You can read more about...

OBS Studio 28+

OBS Studio 28.0.0 and newer have obs-websocket support included in the firmware, so there is not ...

Panasonic Lumix

Tether The Panasonic Lumix only allows 1 network connected client at a time. This means it is no...

Panasonic RP150 Controller Setup

   

Probel SW-P-08/02 Configurable Models

Probel SW-P-08 and SW-P-02 are versatile routing protocols used by many router and video switcher...

Producer Assistant 🔑

Protocol-HTTP Advanced Model

The HTTP Device Core is a generic device core that lets a SKAARHOJ controller talk to any devic...

Protocol-OSC

Open Sound Control (OSC) is a widely used protocol for controlling all sorts of devices. This is ...

PTZ Trace on Blue Pill

PTZ Trace is a feature that simulates the operation of a PTZ (pan-tilt-zoom) camera using pre-rec...

Raw Panel Device Core

The Blue Pill device core, core-skaarhoj-rawpanel, is used by an application like Reactor to forw...

Riedel Smartpanel on Raw Panel Protocol 🔑

The SKAARHOJ Smartpanel application, also known as xpanel-riedelsmartpanel, allows you to integra...

Ross OGP - Model Dump

The Ross OGP core has the ability to capture all device parameter information and save it. This i...

Setup Core-Email

This core will provide you with a quick way to send out emails, from the reactor ecosystem. using...

Sony Mirrorless (FX3, FX2, A7 IV, ...)

This article is written about the FX3, but the same applies to other models connected over USB.Co...

Sony FX6

You can connect to Sony FX6 camera via cabled Ethernet or Wifi. We strongly suggest to use cabled...

Sony ILME-FR7

In order to connect to the SONY ILME-FR7/ILME-FR7K cameras, make sure you have VISCA enabled on t...

Stream Deck on Raw Panel 🔑

With SKAARHOJs Stream Deck application (xpanel-streamdeck package) you can connect one or more St...

Tally-MA on Raw Panel

With SKAARHOJ's Tally-MA application (xpanel-tallyma package), you have the capability to connect...

TCP Device Core / UDP Device Core

The TCP Device Core for Blue Pill, core-protocol-tcp, allows users to send and to some extend rec...

TCP Link for ATEM (on Blue Pill) 🔑

The Blue Pill app called dclink-tcp has a special mode to convert the Blackmagic Design ATEM prot...

TCP Server Device Core

The TCP Server Device Core for Blue Pill, known as core-skaarhoj-tcpserver, enables users to conn...

Tilta Nucleus M

The Tilta Nucleus Core supports control of Tilta Nucleus-M motors via a wired connection. It ope...

Touch on Raw Panel 🔑

With SKAARHOJ's xpanel-touch package for our controllers, users can create software UIs accessibl...

TSL

If you have a PTZ controller you can use TSL as the Routing trigger. That could be beneficial if ...

Vimeo Livestream Studio

Before connecting the core to Livestream Studio first time you need to check in the Hardware Cont...

vMix v25 +

Compatible versions The Blue Pill device core for vMix is compatible with vMix versions 24-29 (c...

Waves Cloud MX

This guide will show you how to connect a Skaarhoj Waveboard to the Waves Cloud MX mixing platfor...

X-keys on Raw Panel 🔑

With SKAARHOJ's X-keys application (xpanel-xkeys package), you have the capability to connect one...

Zoom OSC with XPoint24

How to set up Zoom OSC ZoomOSC is used to managed zoom calls, here is how to set it up Gettin...